Are you looking for an answer to the topic “muchmore fleta euro v2 manual“? We answer all your questions at the website Ppa.aseanseafoodexpo.com in category: Top 731 tips update new. You will find the answer right below.
Table of Contents
How to use Fix mode for Muchmore Fleta USB link
See some more details on the topic muchmore fleta euro v2 manual here:
EURO – Racingline RC
FLETA EURO V2 ESC USER MANUAL. Thank you for purchase of Muchmore Racing FLETA EURO V2 electronic speed controller. New FLETA EURO V2 is specifically …
Source: www.racingline-rc.com
Date Published: 10/24/2021
View: 215
Muchmore FLETA Euro V2 Brushless ESC [High Current BEC …
Specifications: ; BEC Output Switch Mode, 6V/7.4V @5A ; Suitable Motor, Over 9.5T ; Input, 2S LiPo, 2S LiFe, 5-7 cell NiMh/NiCd ; Supported Motor Type, 540 size 2 …
Source: www.mibosport.com
Date Published: 3/30/2021
View: 6800
Muchmore Fleta Pro User Manual – ManualsLib
High-Performance Electronic Speed Control. Fleta Pro controller pdf manual download. Also for: Fleta euro, Fleta stock spec.
Source: www.manualslib.com
Date Published: 2/16/2022
View: 5674
Muchmore Racing Fleta Pro & Fleta Pro V2 Setup Sheets
Fleta Pro V2 Manual · MuchMore · Fleta Pro V2 – Expert V1.4-2 & Blinky V1.4-2 Introduction … Fleta Pro (ProStock/Euro) – Editable Setup Sheet.
Source: site.petitrc.com
Date Published: 7/7/2021
View: 4565
FLETA-PRO_Manual_ENG.pdf
It contains important safety information as well as setup tips from Much-More Racing website. SPECIFICATIONS. ESC Model. FLETA STOCK SPECI. FLETA EURO.
Source: www.the-border.com
Date Published: 3/23/2021
View: 3264
Muchmore FLETA Euro V2 Brushless ESC – RC Car Action
RC Cars & Trucks | News | Traxxas Horizon Hobby Tamiya and more | Readers Re PIT TIPS Nitro RCX Event Coverage | Muchmore FLETA Euro V2 …
Source: www.rccaraction.com
Date Published: 11/28/2022
View: 3799
Muchmore FLETA Euro V2 Brushless ESC (Black)
more easy adjusting the chassis balance. Specifications: Current Continuous: Continuous 80A / Peak 380A. Input: 2S LiPo, 2S LiFe, 5-7 …
Source: www.amainhobbies.com
Date Published: 6/30/2021
View: 6776
Muchmore FLETA Euro V2 Brushless ESC (Black)
This mode more fair control stock race. FLETA EURO V2 is the black translucent case, so you can easily check the mode. … Battery power directly supply to the …
Source: beachrc.com
Date Published: 5/19/2021
View: 2636
Muchmore FLETA Euro V2 Brushless ESC [High Current BEC Ver.]
Features:
FLOW-MAX2™ OPTIMIZED COOLING DESIGN
FLOW-MAX2™ air hole has developed maximum cooling through various tests.
RPM LIMIT FLASHING MODE
FLETA EURO V2 ESC has RPM limit mode features.
With RPM limit mode, ESC controls the limit RPM when driving. This mode controls stock races more fairly. This function runs “Blinky V3.0_25RE2” firmware, easy setup change of normal blinky mode and rev limit blinky mode without firmware update.
FLETA EURO V2 is the black translucent body so you can easily check the mode.
DIRECT MOTOR & ESC FAN PERFORMANCE
Battery power directly powers the fan to cool the ESC and higher RPM motor. The ESC had a separate connector for the motor fan, no soldering required for the motor fan wire.
Optional parts
MR-TU25FAN turbo fan 25x25x10mm
MR-TU30FAN turbo fan 30x30x10mm
MR-TU40FAN turbo fan 40x40x10mm
FLETA EURO V2 ESC fan is directly connected to the battery. However, when ESC turns off, the fan keeps running smoothly. Therefore, battery voltage may drop if left unattended for a long time.
INTERNAL SWITCH SYSTEM
The FLETA EURO V2’s internal switch makes wiring convenient.
– Turn on turn off
– Calibration device
– Speed limit blinky mode <> normal blinky mode
If you want to change the blinky mode, while the device is on, triple-press the setup button.
You can check Blinky mode by LED status.
Normal flashing mode: Green fast flashing
RPM limit Blink mode: 2 green blinks and 1 red blink
COMPACT AND LIGHTWEIGHT DESIGN
The compact and lightweight design of the FLETA EURO V2 ensures a varied layout and plenty of space on the chassis. Easier to adjust chassis balance.
Including 20 x 20mm ESC fan and motor connectors female 3pcs, male 3pcs
Specifications:
MUCHMORE FLETA PRO CONTROLLER USER MANUAL
FLETA PRO / STOCK SPEC / EURO ESC USER MANUAL
Thank you for purchasing the Much-More Racing FLETA PRO / STOCK SPEC / EURO Electronic Speed Control.
The new FLETA PRO / STOCK SPEC / EURO is specially designed for 1/10th scale electric R/C racing.
No matter what class of competition you compete in, the FLETA will help you achieve better results.
Before you start, please read this user manual carefully.
It contains important safety information and setup tips from the Much-More Racing website.
■ PROPERTIES ■
• 2 color LEDs for quick status display.
• Variable drive and braking frequency tuning for expert racing.
• Advanced boost and turbo timing with RPM and throttle control.
• Support for “Blinky” (zero-timing) racing mode.
• Fully configurable throttle and brake response.
• User adjustable low voltage and over temperature protection.
• Cool FLOW-MAX™ aluminum chassis with high-speed 30mm fan.
• Programmable via SHR program card and PC interface.
• User upgradeable firmware.
BASIC INSTALLATION
Soldering battery cables, motor cables and capacitors
Be sure to use a soldering iron with a sufficiently high temperature. Never leave the soldering iron on the attachment point for more than 5 seconds.
If it takes less than 5 seconds for the solder to melt between the solder joints, switch to a higher temperature soldering iron. Overheating the mounting points will damage the ESC.
TURN FLETA ON
Always turn on your transmitter first before turning on your ESC to avoid unexpected motor operation. For your safety, engine operation is automatically disabled until a neutral throttle signal is detected
from the radio receiver.
Sync FLETA and transmitter
In order for the ESC to recognize the full throttle range of your remote control, a throttle range calibration is required.
Before you begin, make sure your 2CH EPA and D/R wireless throttle is set to 100%. Trim and sub-trim should be zero.
Warning: To avoid loss of control or damage and injury, make sure the pinion gear is removed from the motor during the calibration process!
set button
fan
Status LED
Interconnects
program card
Interconnects
3) Press the set button once to set the neutral throttle position.
The green LED will flash to indicate the position has been saved.
5) When the green and red LEDs are solid, hold the full brake and press the set button once.
The LED will flash to indicate the full brake position is stored and will return to green.
LED STATUS INDICATOR
On the front of the ESC there are different colored LEDs for status indication. Please refer to the following table for their meaning:
Green solid
neutral gas
All colors solid
Full throttle / reverse
Red solid
full brake
Flashing green
Zero timing mode
SHR PROGRAM CARD
SHR program card that can adapt the setting to FLETA PRO/STOCK SPEC. (SHR program card needs to be purchased separately)
The FLETA PRO/STOCK SPEC has 19 different program functions.
On the next page you will find a description of the SHR Program Card.
A
–
B
+
BLUE
BLACK
YELLOW
RED
※ Check the cable shrink color
1) Turn on your radio and make sure the throttle stick is in neutral.
Press
the
Green
set button.
LEDs
Press
the
Red &
set button.
Green
LEDs
SAFETY INFORMATION
• Keep this product out of the reach of children.
• This product is designed for use with remote control car models only. It is not suitable for other purposes.
• Never leave this product unattended while connected to a power source.
• Make sure all cables are in good condition and securely fastened.
• Remember that vibration during operation can loosen connections and cause loss of control.
• Do not connect with reversed polarity.
• To avoid short circuits, please ensure that all cables and plugs are properly insulated.
• Keep this product away from water, oil, fuel or other conductive liquids. If this product gets wet,
Stop using it immediately and let it dry completely.
• Do not use excessive force when tightening the fan screws. Overtightening can be permanent
damage the aluminum case.
• Make sure you are using appropriate gear ratios for your track conditions. Unsuitable gear ratios can overload and
damage your speed controller and motor.
• Never use the gas when the engine is not under load. Running the motor with no load can cause this
Damage and risk of fire or burns.
■ SPECIFICATIONS ■
ESC model
Current Continuous
power surge
Entry
Built-in BEC
Matching engine
Supported engine type
size
weight
Pay particular attention to the polarity marking below the attachment point. Make sure you connect everyone
phase (A,B,C) of the motor to the corresponding (A,B,C) attachment point on the ESC.
We recommend using a red wire for the positive (+) battery input connection and a black wire
for the negative pole (-). Connecting a battery with reversed polarity will damage the ESC!!
Remember to solder the included power capacitors to the battery input attachment point!
Running the motor without a capacitor connected will damage the ESC!
connection and assembly
Connect the Rx connector to the throttle channel (CH2) of your radio receiver.
(White shrink tubing is signal wire)
Connect one end of the sensor cable to the motor’s sensor connector and the other end to the ESCs
sensor connection.
C
Use double-sided tape to attach the ESC, power switch and capacitor to the chassis of your model car.
ORANGE
If necessary, install and check the supplied fan with screws on top of the ESC
correct polarity when connecting to the cooling fan power connector.
to press
the
set button.
2) Turn on your ESC while pressing the set button.
Release the Set button when the green LED is solid.
4) When the red LED is solid, hold full throttle and press the set button once.
The LED will flash to indicate the full throttle position is saved.
Be sure to hold full throttle until the LED changes to a different color.
6) Finish the calibration.
Solid Green / Flashing Red
All colors flash
From the LED
Flashing red
1
FLETA PRO
FLETA BEARING SPEC
120A
100A
760A
600A
4-8 cells NiMh/NiCd or 2S LiPo, 2S LiFe
6V@3A
About 3.0T
Over 6.5t
540 size 2 pin brushless with sensor type
30mm (L) x 36mm (W) x 19mm (H)
43g
39g
*FLETA EURO : Factory installed Blinky (Non Boost) firmware.
turn on
your ESC
Press
the
set button.
Over temperature protection activated
No sensor cable detected
Switching on without a signal from the receiver
Motor connection error (A, B, C)
FLETA EURO
80A
480A
Over 9.5 tons
32g
Green
LEDs
Red
LEDs
Muchmore FLETA Euro V2 Brushless ESC
From Muchmore Racing:
FLOW-MAX2™ OPTIMIZED COOLING DESIGN
FLOW-MAX2™ air hole has developed maximum cooling through various tests.
RPM LIMIT FLASHING MODE
FLETA EURO V2 ESC has RPM limit mode features.
With RPM limit mode, ESC controls the limit RPM when driving. This mode controls stock races more fairly. This function runs “Blinky V3.0_25RE2” firmware, easy setup change of normal blinky mode and rev limit blinky mode without firmware update.
FLETA EURO V2 is the black translucent body so you can easily check the mode.
DIRECT MOTOR & ESC FAN PERFORMANCE
Battery power directly powers the fan to cool the ESC and higher RPM motor. The ESC had a separate connector for the motor fan, no soldering required for the motor fan wire.
Optional part
MR-TU25FAN turbo fan 25x25x10mm
MR-TU30FAN turbo fan 30x30x10mm
MR-TU40FAN turbo fan 40x40x10mm
FELTA EURO V2 ESC fan is directly connected to the battery. However, when ESC turns off, the fan keeps running smoothly. Therefore, battery voltage may drop if left unattended for a long time.
INTERNAL SWITCH SYSTEM
The FLETA EURO V2’s internal switch makes wiring convenient.
Turn on turn off
Calibration Setup
Speed limit blinky mode <> normal blinky mode
If you want to change the blinky mode, while the device is on, triple-press the setup button. You can check Blinky mode by LED status.
Normal flashing mode: Green fast flashing
RPM limit Blink mode: 2 green blinks and 1 red blink
COMPACT AND LIGHTWEIGHT DESIGN
The compact and lightweight design of the FLETA EURO V2 ensures a varied layout and plenty of space on the chassis. Easier to adjust chassis balance.
Including 20 x 20mm ESC fan and motor connectors female 3pcs, male 3pcs
Specifications:
Continuous Current: Continuous 80A / Peak 380A
Input: 2S LiPo, 2S LiFe, 5-7 cells NiMh/NiCd
BEC output switching mode: 6V/7.4V at 5A:
Motor Type Supported: 540 size 2 pole brushless with sensor type
Suitable Motor: Over 9.5T:
Size: 26.5*32.7*17mm
Weight: 21.5 g (without cable, condenser and fan)
#ME-FLEV2H
Muchmore Racing is distributed in the US by AMain Hobbies.
Visit MuchmoreRacing.net
See other posts about Muchmore Racing
Sign up today with a subscription to the digital edition or a combination of print and digital!
Related searches to muchmore fleta euro v2 manual
Information related to the topic muchmore fleta euro v2 manual
Here are the search results of the thread muchmore fleta euro v2 manual from Bing. You can read more if you want.
You have just come across an article on the topic muchmore fleta euro v2 manual. If you found this article useful, please share it. Thank you very much.
